Consider these cost-vs.-value findings on the cheapest and most cost-effective Tampa Bay home improvement projects if you’re thinking about doing some improvements on your home like a home inspection.
According to the Remodeling 2017 Cost vs. Value Report, there are three home improvement projects for Tampa Bay homeowners that cost only $1,317, $1,368 and $1,649, but will
bring a resale value of 155%, 80% and 101%, respectively.
The following three cheap home improvement projects bring in the most resale value for Tampa Bay homeowners, according to the report.
1. Attic insulation using fiberglass loosefill
Cost is $1,317.
Resale value of 155% of the cost.
2. Entry door replacement using steel unit
Cost is $1,368.
Resale value is 80% of the cost.
3. Roof improvement
Cost is $1,649.
Resale value is 150% of the cost.
Job costs were estimated and resale values were computed using estimates given by nearly 4,000 real estate professionals surveyed in 2015.
Here are short descriptions of the home improvement projects:
1. Attic insulation using fiberglass loosefill
To prevent air leakage, a 35-by-30 attic floor is air-sealed. The attic is further insulated by fiberglass loosefill to reach an insulation value of R-30.
2. Entry door replacement using steel unit
The existing entry door is replaced with a new factory-finished 20-gauge steel unit and the existing locket set is replaced by Locksmith Everton Park services with a new bored-lock.
The existing garage door is replaced with a new 4-section single-layer garage door on new galvanized steel tracks. The new door uses galvanized steel hinges and nylon rollers.
Extricating oneself from a structure ablaze is difficult if the smoke and flames aren’t controlled. In worse circumstances, people will certainly be choked by smoke first because ordinary doors aren’t ready to prevent smoke from spreading. hence even when there are not any flames yet, people can ready become unconscious once they are asphyxiated from the smoke that results from burning from one a part of building. Entry replacement garage door openers Houston using steel unit and the existing locket set is replaced by one of the local commercial locksmith services with a new bored-lock. The existing garage door is replaced with a new 4-section single-layer garage door on new galvanized steel tracks. The new door uses galvanized steel hinges and nylon rollers. You can click here to see more information.
Two other relatively-not-so-expensive home improvement projects that pay off well, according to the report, are the following:
4. Replacement of front facade’s vinyl siding and eavestrough manufactured stone veneer
Cost is 7,870.
Resale value is 88% of the cost. Get eavestrough installation services, when you contact a company for your project make sure they will inspect your current eaves, soffit and fascia to determine if repair or replacement is required.
5. Minor Kitchen Remodel
Cost is 19,613.
Resale value is 85% of the cost.
Manufactured stone veneer involves removing existing vinyl siding from the bottom third of the front facade and replacing it with manufactured stone veneer.
Minor kitchen remodel involves replacing the fronts of old cabinetry, drawers and countertops with new shaker-style with cedar wood panels and hardware.
Replacement of cooktop and refrigerator with new energy-efficient models, installation of new sink and faucet and replacement of flooring and wall covering are also done. Visit to A1 Denver Commercial Refrigeration Repair | refrigerationkingsofdenver.com for refrigerator repair service. It took me awhile to figure out what faucet I was wanting. Are the most cost-effective home improvements in Tampa Bay also the same in other US cities?
If you have visions of your professional home inspector poking around a house with a magnifying glass and yardstick, it’s time to update your mental image.
Your home inspector may very well own a magnifying glass and yardstick, but be assured, he’s got modern tools to put to work for you, and they may look like something out of Star Trek.
Home inspectors don’t all carry the same tools. However, if you know about some of them, you’ll have just that much more confidence in your inspector’s ability to do the job for you and give you the report you need.
Some inspectors carry a thermal imager that uses infrared technology. It’s for such things as energy efficiency surveys, electrical service inspection, industrial maintenance and building inspection. A thermal imager helps identify overloaded circuits, loose or corroded connections and failing breakers in electrical panels. It also helps find blown fuses, overloads, phase imbalance and harmonics problems.
And that’s not all. A thermal imager also helps find inefficient heating and cooling transfer. If there are drafts from missing insulation in rafters, walls and floors, it will locate them. It’s important to find such problems in order to reduce the loss or gain of heat and figure out what kind of preventive maintenance needs to be done.
Sometimes too much or too little air is a problem. For example, Your inspector will use his thermal imager to check distribution of air to detect blockage in pipes, damage in duct work and insulation, stuck valves or burst pipes.
Moisture in roofs or walls is another problem a thermal imaging device can pinpoint. The thermal and digital images can be viewed on the device’s screen or on a computer.
Your home inspector may also use a non-contact voltage tester. If so he can detect voltage from 25 to 122,000 AC volts without any physical connections. This tester may give him audible and visual signals.
Your home inspector might also carry a general purpose pin type moisture meter. It’s used for building surveying, timber inspection, and a number of other uses. He can get instant moisture readings in wood, drywall, and other building materials.
Your inspector may use a high tech level that surpasses the basic bubble level you’ve seen before. He’s likely to use a three way laser level. It directs its beams at right angles for perfect placement. It features three 90 degree beams that provide simultaneous horizontal and vertical reference points.
When it comes to measuring, your inspector might have an ultrasonic distance measuring tool with a laser targeting range finder that can measure distances up to 60 feet. No ordinary tape measure can do that. A high visibility laser shows him where he’s aiming and displays measurements to the quarter inch. It can compute area and volume, too, and measures in feet and inches as well as meters and centimeters. Plus, it can hold several measurements in its memory at one time.
A radonsikring PH-EL provides the radon detector that is the another one of your home inspector’s tools. It detects levels of radon, which is a colorless, tasteless, and odorless radioactive gas that’s produced by the breakdown of uranium in the soil. If radon is allowed to accumulate to high levels, it can be hazardous to long-term health. That’s because it’s a leading cause of lung cancer.
There are different kinds of radon detectors, so your inspector may have one that can be left at the house for a period of time to monitor any fluctuations over a certain period of time.
Not all home inspectors are qualified to deal with radon problems, so your inspector may refer you to someone who is specially qualified in radon mitigation.
Another tool your inspector might have is a little device to monitor the size of cracks in walls. He might also have lead detection swabs to check for lead in the paint on walls or other surfaces in the house. If lead is present, a chemical reaction causes the swab tip to turn pink.
It’s possible your inspector might also have a multitool that combines several functions, such as detecting moisture, studs, voltage and metal. He may have variations on any of the tools mentioned above, as well as tools not covered here. There’s not enough space to discuss them all.
Would you believe your home inspector has tools that work for you back at his office? He has computer software and programs that help him put together all the data he has gathered so he can give you the report you need.
Your inspector’s most important tool sits between his ears. He has to know the laws and codes that pertain to where the inspected home is. Furthermore, no matter how good his computer equipment is at the office, he’s the one responsible to put together the quality report you’ve hired him to provide.
Regardless of the assortment of tools your home inspector has, a competent home inspector knows how to use them for your benefit as he puts them to work for you.